Fly a Hot-Air Balloon: lesson plan
Students fly a hot-air balloon with only two controls, burn and vent, and use the readings to explain why hot air rises, how much a balloon can lift, and how pilots steer by changing height to find the right wind.
- Ages
- 11–16 (grades 6–10)
- Time
- 50 minutes
- Subject
- Physics: density, upthrust and the atmosphere
- You need
- Devices with a browser (one per pair), calculators, results table; optional demo: a sky lantern or bin-bag balloon with a hairdryer, or a balloon on a flask in hot water
Open Fly a Hot-Air Balloon Jump to the quiz
Learning objectives
By the end of the lesson, students can:
- Explain, using particles, why heating air lowers its density.
- Describe upthrust (buoyancy) and state that a balloon rises when upthrust is greater than its total weight.
- Calculate the lift of a hot-air balloon from its volume and the difference in air density inside and outside.
- Explain how a balloon pilot uses winds at different heights to travel in a chosen direction, and why the air gets colder and thinner with height.
Key vocabulary
- Density
- Mass per unit volume: ρ = m / V. Air at sea level and 15 °C has a density of about 1.225 kg/m³.
- Upthrust (buoyancy)
- The upward force from a fluid on an object in it, equal to the weight of fluid the object pushes aside.
- Envelope
- The fabric bag of a hot-air balloon. A typical one holds about 2,800 m³ of air.
- Absolute temperature
- Temperature measured in kelvin from absolute zero: K = °C + 273.15. Gas density is inversely proportional to it.
- Lapse rate
- How fast the air cools with height: about 6.5 °C per kilometre in the standard atmosphere.
- Wind shear
- A change in wind speed or direction with height. Balloon pilots rely on it to steer.
Background for the teacher
At the same pressure, the density of air is inversely proportional to its absolute temperature (from the ideal gas law, ρ = pM/RT). Heating the air inside an envelope from 15 °C (288 K) to 80 °C (353 K) makes it 288/353 ≈ 0.82 times as dense, about 18% lighter. With outside air at 1.225 kg/m³, the inside air is about 1.00 kg/m³. The difference, 0.225 kg/m³, across a 2,800 m³ envelope is about 630 kg: that is the mass the balloon can lift, including envelope, basket, burner, fuel and people. In force terms, lift = V g (ρoutside − ρinside) ≈ 6,200 N. Envelopes run at roughly 80–100 °C and fabric is usually limited to about 120 °C.
The game calculates this buoyant force continuously. The envelope always loses heat, so the pilot must burn in bursts to stay level, and the balloon responds slowly because it must accelerate its own mass plus about three tonnes of air inside it. With height, the air cools by about 6.5 °C per kilometre and gets thinner, so a hotter envelope is needed to float high up. Winds differ between layers, often in direction as well as speed, which is the only way to steer: each of the eight flights (from First hop to Hare and hound) has a different stack of winds. The first crewed hot-air flight was in Paris on 21 November 1783, in a Montgolfier balloon.
Warm-up (5 minutes)
- Ask: "Why does a hot-air balloon go up? What is actually lighter than what?" Collect ideas.
- Ask: "A balloon has no steering wheel and no engine pushing it sideways. How do you think pilots get where they want to go?"
- Optional demo: place a balloon over the neck of an empty flask and stand it in hot water. Ask students to explain why the balloon inflates.
Activity with the game
- Pairs open Fly a Balloon and play First hop. Hold Burn to heat the envelope and Vent to let hot air out (or the up and down arrow keys). The HUD shows height, vertical speed, inside temperature and fuel; the second line shows distance to the X and the wind at the balloon’s height.
- Hover data: pairs try to hold the balloon level at about 100 m, 400 m and 800 m (in First hop or The long field). At each height they record the inside temperature needed to hover. Does it rise with height? Link to the colder, thinner air.
- Wind map: on Back again, the bottom wind blows the wrong way. Pairs climb slowly, recording the wind direction and speed at each height band from the arrows, and sketch a wind profile before using it to reach the X.
- Calculation: using the background numbers, pairs calculate the lift of a 2,800 m³ envelope at 80 °C on a 15 °C day, then redo it for a hot summer day of 30 °C outside. Why do balloonists prefer cool mornings?
- Challenge flights: Over the river, Tight landing and Switchbacks. Land below about 2 m/s and close to the X for three stars. Pairs note how early they had to stop burning to land gently, and explain why the balloon responds slowly.
- Plenary: pairs write a three-step "pilot’s guide" explaining how to travel left when the surface wind blows right, using the words density and upthrust.
Discussion questions
- Why does heating the air make the balloon rise?
Show a model answer
Heated air particles move faster and spread further apart, so the same volume of air has less mass: its density drops. The envelope’s upthrust equals the weight of the cooler outside air it displaces. When the hot air plus the balloon weighs less than that, there is a resultant upward force.- Why did you need a hotter envelope to hover higher up?
Show a model answer
Higher up the outside air is thinner (lower pressure) and so less dense, which means less upthrust for the same envelope. Even though it is colder, the balloon needs a bigger density difference, so the inside must be heated more.- Why can a balloon lift more on a cold morning than on a hot afternoon?
Show a model answer
Lift depends on the density difference between outside and inside. Cold outside air is denser, so with the same envelope temperature the difference is bigger. At 15 °C outside and 80 °C inside the difference is about 0.225 kg/m³; at 30 °C outside it drops to about 0.17 kg/m³, a quarter less lift.- Why does the balloon keep rising for a while after you stop burning?
Show a model answer
The envelope is still hotter than needed, and the balloon has a lot of inertia: it must slow down its own mass and several tonnes of air inside it. Pilots learn to burn early and stop early, then wait.- How do pilots steer?
Show a model answer
They cannot push sideways, so they change height to find a layer of wind blowing the way they want, ride it, then climb or descend into another. Before take-off they often release a small helium balloon to see the wind at each level.
Common misconceptions
- Heat rises, so hot air is pulled upwards.
- Nothing pulls hot air up. Hot air is less dense, and the denser surrounding air is pulled down by gravity more strongly, pushing the hot air up. Upthrust is the result of this pressure difference.
- Hot-air balloons can be steered with the burner.
- The burner only changes height. Sideways travel comes entirely from the wind, which is why the choice of height matters.
- Heating air makes its particles bigger.
- The particles stay the same size. They move faster and the gas expands, so they are spaced further apart and the density falls.
Quick quiz
Why is hot air less dense than cold air?
- Its particles are smaller
- Its particles are further apart, so there is less mass in each cubic metre
- It contains less oxygen
- It is lighter than nothing
Answer
B. Faster-moving particles spread out, so the same volume has less mass.
A balloon floats steadily at one height. What is true?
- Upthrust is greater than weight
- Upthrust equals weight
- Weight is greater than upthrust
- There is no gravity on it
Answer
B. Balanced forces mean no acceleration, so it neither rises nor falls.
A 2,800 m³ envelope has a density difference of 0.2 kg/m³. About what mass can it lift?
- 14 kg
- 56 kg
- 560 kg
- 14,000 kg
Answer
C. 2,800 × 0.2 = 560 kg, which includes the envelope, basket, fuel and passengers.
Air at 15 °C is heated to 80 °C at the same pressure. Roughly how much less dense does it become?
- About 2%
- About 18%
- About 50%
- About 80%
Answer
B. Density scales as 1/T in kelvin: 288/353 ≈ 0.82, so about 18% less dense.
How does a balloon pilot travel in a chosen direction?
- With a propeller
- By tilting the basket
- By changing height to find a wind blowing that way
- By venting air sideways
Answer
C. Winds change with height; picking the right layer is the only steering a balloon has.
In the standard atmosphere, how much colder is it 2 km up than at the ground?
- About 2 °C
- About 6.5 °C
- About 13 °C
- About 65 °C
Answer
C. The lapse rate is about 6.5 °C per km, so 2 km gives about 13 °C colder.
Going further
- Calculate: use the hot-air balloon lift calculator to find how big an envelope must be to lift a 400 kg load on a 25 °C day with the inside at 100 °C.
- Build a bin-bag hot-air balloon (tissue paper or a thin plastic bag) and inflate it with a hairdryer. Measure how long it stays up and relate it to how quickly it cools.
- History: research the Montgolfier brothers’ first public flights in 1783, including the test flight with a sheep, a duck and a cockerel, and the first crewed flight on 21 November.
Calculators for this lesson
Curriculum links
- England National Curriculum, KS3 Physics: atmospheric pressure decreasing with increase of height; upthrust effects, floating and sinking.
- England National Curriculum, KS3 Physics: changes with temperature in motion and spacing of particles; density calculated from mass and volume.
- NGSS MS-PS1-4: develop a model that predicts and describes changes in particle motion, temperature, and state of a pure substance when thermal energy is added or removed.
- GCSE Physics: the particle model and density; pressure in fluids and upthrust (separate science).
The science in this plan matches the notes and sources under Fly a Hot-Air Balloon. Free to use and adapt for teaching. Ideas or corrections: hello@notebookfun.com.