Torque calculator

How strong is a turning force? Enter the force, the distance from the pivot and the angle you push at to get the torque, and add a rotation speed to get the power.

A firm one-handed pull 100–200 N; standing on a spanner with 70 kg is about 690 N
Wheel brace 0.35–0.45 m, door handle about 0.75 m from the hinge, bike crank 0.17 m
°
90° (pushing square-on) gives the most torque; 0° (pushing along the lever) gives none
rpm
Petrol engine at peak torque 2,000–4,500 rpm, cyclist’s cadence 80–100 rpm
Torque–
Force component that turns–
Power at that rotation speed–

See it for real: play Build a Trebuchet or play Stack It or play Topple the Dominoes.

The formula

Torque, also called the moment of a force, is the turning effect of a force about a pivot. It depends on how hard you push, how far from the pivot you push, and the direction you push in:

τ = F r sin θ   and the power at angular speed ω   P = τ ω = τ × 2π × rpm / 60

Here τ (tau) is the torque in newton-metres (N·m), F the force in newtons, r the distance from the pivot to where the force acts, and θ the angle between the force and the line from the pivot. The part r sin θ is the perpendicular distance from the pivot to the line of the force, sometimes called the moment arm. At GCSE this is usually written moment = force × perpendicular distance.

Why a longer spanner helps

Torque grows in proportion to distance, so doubling the length of a spanner halves the force you need. That is the secret of every lever. A door handle sits as far from the hinges as possible for the same reason; try pushing a door open near its hinge and you will need several times the force. Archimedes is said to have boasted that with a long enough lever and a place to stand he could move the Earth.

The angle matters too. Pushing at right angles (90°) uses all of your force. At 30°, sin 30° = 0.5, so only half of it turns the spanner; the rest just pulls along the handle. At 0° nothing turns at all.

Balanced moments

An object is balanced when the clockwise and anticlockwise torques about any pivot are equal. A 30 kg child sitting 2 m from the centre of a see-saw balances a 40 kg adult 1.5 m from the centre on the other side, since 30 × 2 = 40 × 1.5. A trebuchet uses the same idea in reverse: a heavy counterweight on a short arm swings a light stone on a long arm very fast. Stacks topple when the weight of the top part acts outside the edge of its support, creating an unbalanced torque.

Typical torques

JobTorque
Opening a tight jam jar lid2–5 N·m
Bicycle pedal, hard push (300 N on a 0.17 m crank)about 50 N·m
Car wheel nuts80–140 N·m
Small petrol car engine, peak100–150 N·m
Family diesel or turbo petrol engine, peak250–400 N·m
Electric car motor, from standstill300–1,000 N·m
Large cordless drill, top setting50–100 N·m

Torque, rpm and horsepower

Power is how fast work is done, and for something spinning it is torque times angular speed. An engine making 300 N·m at 3,000 rpm produces 300 × 2π × 3,000 / 60 ≈ 94 kW (126 hp). That is why a car’s power figure is quoted at a higher rpm than its torque peak: torque may fall a little as revs rise, but power keeps rising for a while because the shaft turns faster. In imperial units, horsepower = torque in lb·ft × rpm / 5,252, which is why torque and horsepower curves always cross at 5,252 rpm.

Assumptions and limits

Everyday uses

Tune the counterweight of a lever in Build a Trebuchet, find the tipping point of tall, thin objects in Stack It, and watch each falling domino’s weight topple the next in Topple the Dominoes.

Worked example

Your car’s wheel nuts need tightening to 110 N·m, a typical figure for a family car. The wheel brace is 40 cm long. How hard do you push on the end, at right angles?

Force280 N
Distance from the pivot (lever arm)0.4 m
Angle between force and lever90 °
Rotation speed (optional, for power)0 rpm
Torque112 N·m
Force component that turns280 N
Power at that rotation speed0 W

A 280 N push (like hanging about 29 kg on the end) gives 112 N·m, just over the target. Push at 45° instead and you need 40% more force for the same torque. Proper wheel-nut tightening uses a torque wrench, because over-tightening can stretch the studs.

Frequently asked questions

What is the formula for torque?
τ = F × r × sin θ, where F is the force, r the distance from the pivot and θ the angle between them. Pushing with 50 N at right angles on the end of a 0.3 m spanner gives 50 × 0.3 × 1 = 15 N·m.
How do I convert N·m to lb·ft?
Divide by 1.3558. So 100 N·m is 73.8 lb·ft, and 250 lb·ft is 339 N·m. One kgf·m, still seen on older specifications, is 9.81 N·m.
What is the difference between torque and horsepower?
Torque is the twisting force; power is how quickly that twisting does work. Power = torque × angular speed, so the same torque at twice the rpm is twice the power. In imperial units hp = lb·ft × rpm / 5,252.
Why does a longer wrench make it easier to undo a bolt?
Because torque is force times distance. A 40 cm wrench needs half the force of a 20 cm one for the same torque, so a stuck wheel nut that needs 150 N·m takes 375 N on the long one and 750 N on the short one.
What is the unit of torque?
The newton-metre (N·m) in SI. In the US and on many tools pound-feet (lb·ft) and pound-inches (lb·in) are also used; 1 lb·ft = 1.356 N·m and 1 lb·in = 0.113 N·m.
Is torque the same as a moment?
Yes, in everyday use. Physicists usually say torque and engineers often say moment (as in “bending moment”); both mean force times perpendicular distance from a pivot.

Sources

Related calculators

Play it